Tel :+962 6 4385767   Fax :+962 6 4384439  Email


Gear Pumps
A Series
Geared for top performance, Roper Pumps’ “A” Series keep your operation moving through thick and thin.


Gear Pumps
AE Series
Geared for top performance, Roper Pumps’ “A” Series keep your operation moving through thick and thin.

artAE19 asm

Gear Pumps
F Series
Roper Pumps’ “F” Series gives you eight great ways to deliver under pressure.



  • Cast iron standard construction
  • Capable of operating at nominal motor speeds
  • Self priming capabilities
  • Bi-Rotational
  • Pressure up to 300 PSI
  • Flows up to 75.6 GPM



  • Cast iron construction
  • Capable of operating at nominal motor speeds
  • Pressures up to 300psi
  • Flows up to 135gpm
  • Bi-directional rotation
  • Helical gears for quiet operation
  • Bearings and wear-plates are wear-resistant, high lead bronze

  • High pressure external gear pump
  • Capable of handling pressures to 300 PSI in standard construction
  • 425 PSI with bearing modifications
  • Front pullout design, maintenance without disturbing piping
  • Flanged sleeve bushings with grooves to allow for lubrication
V Series
With its magnetic power and leak-proof performance, the V Series will protect your operation.







  • Magnetic drive, seal-less helical gear pump
  • Neodymium magnets up to 5ft/lb torque
  • Stainless steel containment shell
  • Ductile iron housing with hardened steel shafts and gears



  3600 Series
There must be 3600 easy ways to put these ultra-reliable workhorses to use.










  • Heavy duty cast iron helical gear pumps
  • Bi-directional, self-priming
  • Differential pressures to 125 PSI
  • Up to 468 GPM
  • Standard operation up to 212°F
  • Can be built to operate up to 450°F
  • Maintenance-free durability



Z Series
A reliable performer, Roper Pumps’ “Z” Series is open to easy maintenance and has a wide choice of seals.




  • Cast iron helical gear pump
  • Two-piece backplate for flexible sealing options
  • Many parts interchangeable with 3600 series
  • Differential pressures to 125 PSI
  • Up to 165 GPM




             3800 Series



  • Differential pressures up to 125 psi
  • Up to 540 gpm (2 M3/min)
  • Multi-lip grease purges seal assembly
  • Maintenance indicator / Weep detection
  • Triple shaft seals plus sealed ball bearings
  • Over pressure relief type grease fittings
  • Bi-directional rotation
2835 Series
When the going gets thick, this pump gets going, count on it every time.



  • Angled gear arrangement
  • Enlarged ports facilitate pumping
  • Low horsepower requirements allow use of low cost drivers
  • Pressures up to 75 PSI
  • Capacities up to 11.3 GPM



                     4400 Series
Tank truck pumps for fleets hauling crude oil, condensate, waste oil, and other abrasive materials



  • Quick-fit seal cartridge offers one-step seal replacement
  • Four heavy-duty ball bearings give positive support to pumping gears
  • Large shaft diameters minimize shaft deflection at higher operating pressures
  • Wear-resistant bronze seal cartridges act as a bushing in the event of a bearing failure


Contact Us
PECO - Professional Engineers T.A.
Amman - Jordan
Al-Yasmeen, Jabal Arafat St.
Building No. 40, 2nd Floor
Tel. +962 6 4385767
Fax.+962 6 4384439

Copyright © 2014 PECO – Professional Engineers T.A. All rights reserved.

Home About Contact Sitemap

Disclaimer : A confirmation of reading and acceptance of the Disclaimer otherwise user can’t see our PDF or software or whatever information we see it might be a chance of problems from end user mistake or wrong usage.